Toevoegen aan favorieten · Meld misbruik
Advertentiedetails
| Vraagprijs | N.o.t.k. |
|---|---|
| Verzendkosten | Exclusief |
| Staat | Nieuw |
| Garantie | Nee |
| Ouderdom | 60 maanden |
| Verzending | ophalen en (pakket)post nationaal |
| Betaling | contant en bank vooraf |
Beschrijving
Myricom (10G-PCIE2-8C2-2S+SNF) Dual SFP+ Ports, PCIe Gen2 x8
Netwerkkaart met 2x 10Gbit SFP poorten, wordt geleverd zoals op de foto's dus zonder SFP's!
Heeft altijd als spare op de plank gelegen en is nu niet meer nodig. Was bij aanschaf duur.. doe een leuk bod en wie weet heb je straks bandbreedte over ;-)
Opsturen is geen probleem mits het in Nederland is.
Voor de specs even lekker een knip-plak....
Specs:
For 10GBase-SR, 10GBase-LR, and Direct Attach
(does not include an SFP+ fiber transceiverSFP+-terminated "Direct Attach" twinax copper cables)
Key Features::
• Low-profile PCI Express x8 add-in card
• Dual-protocol network ports, 10-Gigabit Ethernet or 10-Gigabit Myrinet
• Wire-speed performance from both network ports concurrently
• "Gen2" (5 GT/s) PCI Express x8 host port
• Firmware-controlled stateless offloads
• 14.7 Watts typical including power for two SFP+ transceivers
• MTBF: 5M hours (FIT rate = 200)
Introduction:
This Network Adapter appears to the host operating system as two independent PCI Express devices, one for each network port. Each of the two devices (Lanai-Z8ES chips) can carry traffic at rates approaching 10Gb/s (~9.9 Gb/s with a 9KB MTU, or ~9.5 Gb/s with a 1500B MTU). Together, the two devices can carry traffic between the host and the network at rates approaching 20Gb/s.
If both devices are using the bundled Myri10GE Ethernet software distribution and if the hosts have sufficient memory bandwidth, the netperf TCP_STREAM test with two streams shows an aggregate bandwidth of ~19.8 Gb/s with a 9KB MTU, and ~18.9 Gb/s with a 1500B MTU. These netperf 2.4.3 tests were between pre-release Intel Nehalem hosts running the RHEL5 kernel 2.6.18-92.el5. Performance will vary with the host and operating system.
Specifications:
Myri-10G network ports (2):
SFP+ (Small Form factor Pluggable) sockets for SFP+ transceivers, either 10GBase-SR or 10GBase-LR, 10+10 Gbit/s data rate, full-duplex. The SFP+ sockets provide SFI 10.3125 GBaud 64b/66b-encoded signaling, electrical power, and the standard SFP+ management interface. The sockets do not require the use of SFP+ transceivers purchased from Myricom. The sockets may also be used with SFP+-terminated twinax "Direct Attach" copper cables up to 7m, or with SFP+-terminated EOE cables. The ports can operate with either Ethernet or Myrinet protocols at the Data Link layer. When operating in Ethernet mode, the port supports Ethernet flow control as defined by IEEE 802.3x. The allowed length of the fiber cable depends upon the SFP+ transceiver and the quality of the fiber, but in Myrinet mode must not exceed 200m due to Myrinet flow control. (See this Guide to Myri-10G PHYs (pdf).)
Laser Safety:
When used with 10GBase-SR or 10GBase-LR SFP+ transceivers, this Network Adapter is a Class 1 Laser Product (no biological hazard).
PCI Express host port:
This Network Adapter is an x8 (8 lane) "Gen2" (5 GT/s) PCI Express Add-in Card. It is capable of exchanging data with a host computer at up to 4 GBytes/s (500 MBytes/s per lane) data rate in each direction, full-duplex. This Network Adapter is fully compliant with the PCI Express Card Electromechanical Specification Rev. 2.0, and with the PCI Express Base Specification Rev. 2.0 at 5 GT/s or 2.5 GT/s. The circuit-board edge connector of the Network Adapter will fit mechanically in x8 or x16 physical slots in host computers. The Network Adapter auto-negotiates operation in the widest available mode (x8, x4, x2, or x1) and highest data rate (5 or 2.5 GT/s) supported by the slot it is plugged into.
Optional PCI Express capabilities supported: Advanced Error Reporting, Function-Level Reset, Device Serial Number, up to 16 outstanding read requests, up to 2KB MaxPayloadSize for all packet types, MSI and MSI/X, SMBus access.
These "Gen2" PCI Express network adapters will operate correctly in "Gen1" (2.5 GT/s) PCI Express slots in a host, but require "Gen2" (5 GT/s) PCI Express slots to achieve full performance.
Network Adapter processors and memories(2):
The Network Adapter is based on two Myricom Lanai Z8ES chips bridged to the host port with a PCI Express switch chip. Each Lanai Z8ES includes a programmable RISC, a set of packet engines, and 2MB of fast SRAM. The RISC, packet engines, and SRAM inside the Lanai-Z8ES chip operate at a clock rate of 364.6MHz. Byte parity is generated and checked on all on-chip memories.
EEPROM (2):
1MB, which includes the firmware required for PCI device initialization and an Etherboot (UEFI- and PXE-compatible) driver. The driver loads the matching firmware as required by the mode in which the Network Adapter is operating. The EEPROM can be re-programmed in-place by the Lanai Z8ES.
LEDs (4):
The yellow LEDs on the PCI faceplate are controlled by the firmware running in the Lanai for this port. The interpretation of the yellow LEDs is different for different firmware. There is also a green LED for each port: off indicates that the link is down, on indicates that the link is up, and blinking indicates traffic.
Physical characteristics:
The circuit board is a low-profile add-in card as defined in the PCI Express Card Electromechanical Specification Rev. 2.0: height 68.9mm (exclusive of the PCI faceplate), length 167mm (exclusive of the PCI faceplate), total thickness 22mm, weight 83.5g (0.184 pound) including the standard PCI faceplate. The Network Adapter can be supplied with either a standard PCI faceplate (10G-PCIE2-8B2-2S) or a low-profile PCI faceplate (10G-PCIE2-8B2L-2S).
Power:
The Network Adapter is powered from both 3.3V and 12V from the PCI Express port. The 3.3V current including transceivers in both ports is 1.8A (5.9W) typical, 2A (6.6W) maximum. When the network ports are used with "Direct Attach" twinax copper cables, the current is 1.2A (4W) typical, 1.3A (4.3W) maximum. The 12V current is 0.73A (8.8W) typical, 0.80A (9.6W) maximum. Total power with transceivers in both slots is 14.7W typical, 16.2W maximum.
Environmental:
Operating: Temperature 0C to 55C up to 10,000 foot altitude with 100LFM minimum airflow. Relative humidity 15% to 80% @ 50C, non-condensing. Storage: Temperature -40C to 70C. Relative humidity 90% @ 65C.
Netwerkkaart met 2x 10Gbit SFP poorten, wordt geleverd zoals op de foto's dus zonder SFP's!
Heeft altijd als spare op de plank gelegen en is nu niet meer nodig. Was bij aanschaf duur.. doe een leuk bod en wie weet heb je straks bandbreedte over ;-)
Opsturen is geen probleem mits het in Nederland is.
Voor de specs even lekker een knip-plak....
Specs:
For 10GBase-SR, 10GBase-LR, and Direct Attach
(does not include an SFP+ fiber transceiverSFP+-terminated "Direct Attach" twinax copper cables)
Key Features::
• Low-profile PCI Express x8 add-in card
• Dual-protocol network ports, 10-Gigabit Ethernet or 10-Gigabit Myrinet
• Wire-speed performance from both network ports concurrently
• "Gen2" (5 GT/s) PCI Express x8 host port
• Firmware-controlled stateless offloads
• 14.7 Watts typical including power for two SFP+ transceivers
• MTBF: 5M hours (FIT rate = 200)
Introduction:
This Network Adapter appears to the host operating system as two independent PCI Express devices, one for each network port. Each of the two devices (Lanai-Z8ES chips) can carry traffic at rates approaching 10Gb/s (~9.9 Gb/s with a 9KB MTU, or ~9.5 Gb/s with a 1500B MTU). Together, the two devices can carry traffic between the host and the network at rates approaching 20Gb/s.
If both devices are using the bundled Myri10GE Ethernet software distribution and if the hosts have sufficient memory bandwidth, the netperf TCP_STREAM test with two streams shows an aggregate bandwidth of ~19.8 Gb/s with a 9KB MTU, and ~18.9 Gb/s with a 1500B MTU. These netperf 2.4.3 tests were between pre-release Intel Nehalem hosts running the RHEL5 kernel 2.6.18-92.el5. Performance will vary with the host and operating system.
Specifications:
Myri-10G network ports (2):
SFP+ (Small Form factor Pluggable) sockets for SFP+ transceivers, either 10GBase-SR or 10GBase-LR, 10+10 Gbit/s data rate, full-duplex. The SFP+ sockets provide SFI 10.3125 GBaud 64b/66b-encoded signaling, electrical power, and the standard SFP+ management interface. The sockets do not require the use of SFP+ transceivers purchased from Myricom. The sockets may also be used with SFP+-terminated twinax "Direct Attach" copper cables up to 7m, or with SFP+-terminated EOE cables. The ports can operate with either Ethernet or Myrinet protocols at the Data Link layer. When operating in Ethernet mode, the port supports Ethernet flow control as defined by IEEE 802.3x. The allowed length of the fiber cable depends upon the SFP+ transceiver and the quality of the fiber, but in Myrinet mode must not exceed 200m due to Myrinet flow control. (See this Guide to Myri-10G PHYs (pdf).)
Laser Safety:
When used with 10GBase-SR or 10GBase-LR SFP+ transceivers, this Network Adapter is a Class 1 Laser Product (no biological hazard).
PCI Express host port:
This Network Adapter is an x8 (8 lane) "Gen2" (5 GT/s) PCI Express Add-in Card. It is capable of exchanging data with a host computer at up to 4 GBytes/s (500 MBytes/s per lane) data rate in each direction, full-duplex. This Network Adapter is fully compliant with the PCI Express Card Electromechanical Specification Rev. 2.0, and with the PCI Express Base Specification Rev. 2.0 at 5 GT/s or 2.5 GT/s. The circuit-board edge connector of the Network Adapter will fit mechanically in x8 or x16 physical slots in host computers. The Network Adapter auto-negotiates operation in the widest available mode (x8, x4, x2, or x1) and highest data rate (5 or 2.5 GT/s) supported by the slot it is plugged into.
Optional PCI Express capabilities supported: Advanced Error Reporting, Function-Level Reset, Device Serial Number, up to 16 outstanding read requests, up to 2KB MaxPayloadSize for all packet types, MSI and MSI/X, SMBus access.
These "Gen2" PCI Express network adapters will operate correctly in "Gen1" (2.5 GT/s) PCI Express slots in a host, but require "Gen2" (5 GT/s) PCI Express slots to achieve full performance.
Network Adapter processors and memories(2):
The Network Adapter is based on two Myricom Lanai Z8ES chips bridged to the host port with a PCI Express switch chip. Each Lanai Z8ES includes a programmable RISC, a set of packet engines, and 2MB of fast SRAM. The RISC, packet engines, and SRAM inside the Lanai-Z8ES chip operate at a clock rate of 364.6MHz. Byte parity is generated and checked on all on-chip memories.
EEPROM (2):
1MB, which includes the firmware required for PCI device initialization and an Etherboot (UEFI- and PXE-compatible) driver. The driver loads the matching firmware as required by the mode in which the Network Adapter is operating. The EEPROM can be re-programmed in-place by the Lanai Z8ES.
LEDs (4):
The yellow LEDs on the PCI faceplate are controlled by the firmware running in the Lanai for this port. The interpretation of the yellow LEDs is different for different firmware. There is also a green LED for each port: off indicates that the link is down, on indicates that the link is up, and blinking indicates traffic.
Physical characteristics:
The circuit board is a low-profile add-in card as defined in the PCI Express Card Electromechanical Specification Rev. 2.0: height 68.9mm (exclusive of the PCI faceplate), length 167mm (exclusive of the PCI faceplate), total thickness 22mm, weight 83.5g (0.184 pound) including the standard PCI faceplate. The Network Adapter can be supplied with either a standard PCI faceplate (10G-PCIE2-8B2-2S) or a low-profile PCI faceplate (10G-PCIE2-8B2L-2S).
Power:
The Network Adapter is powered from both 3.3V and 12V from the PCI Express port. The 3.3V current including transceivers in both ports is 1.8A (5.9W) typical, 2A (6.6W) maximum. When the network ports are used with "Direct Attach" twinax copper cables, the current is 1.2A (4W) typical, 1.3A (4.3W) maximum. The 12V current is 0.73A (8.8W) typical, 0.80A (9.6W) maximum. Total power with transceivers in both slots is 14.7W typical, 16.2W maximum.
Environmental:
Operating: Temperature 0C to 55C up to 10,000 foot altitude with 100LFM minimum airflow. Relative humidity 15% to 80% @ 50C, non-condensing. Storage: Temperature -40C to 70C. Relative humidity 90% @ 65C.